Refer to the exhibit. What method can be used to enable an OSPF router to advertise a default route to neighboring OSPF routers?

Last Updated on November 23, 2020 by Admin Refer to the exhibit. What method can be used to enable an OSPF router to advertise a default route to neighboring OSPF routers? Use a static route pointing to the ISP and redistribute it. Use the default-information originate command on ISP. Use the redistribute static command on […]
Continue reading…

 

A network administrator has been tasked with creating a disaster recovery plan. As part of this plan, the administrator is looking for a backup site for all of the data on the company servers. What service or technology would support this requirement?

Last Updated on November 23, 2020 by Admin A network administrator has been tasked with creating a disaster recovery plan. As part of this plan, the administrator is looking for a backup site for all of the data on the company servers. What service or technology would support this requirement? virtualization data center software defined […]
Continue reading…

 

Refer to the exhibit. The network administrator has an IP address of 192.168.11.10 and needs access to manage R1. What is the best ACL type and placement to use in this situation?

Last Updated on November 23, 2020 by Admin Refer to the exhibit. The network administrator has an IP address of 192.168.11.10 and needs access to manage R1. What is the best ACL type and placement to use in this situation? standard ACL inbound on R1 vty lines standard ACL inbound on R2 WAN interface connecting […]
Continue reading…

 

What command would be used as part of configuring NAT or PAT to identify an interface as part of the external global network?

Last Updated on November 23, 2020 by Admin What command would be used as part of configuring NAT or PAT to identify an interface as part of the external global network? access-list 10 permit 172.19.89.0 0.0.0.255 ip pat inside ip nat inside ip nat outside For more question and answers: Click Here CCNA3 v7 – ENSA Final […]
Continue reading…

 

Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?

Last Updated on November 23, 2020 by Admin Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem? Interface Fa0/0 is configured as a passive-interface on router R2. Interface s0/0 has not been activated for OSPFv2 […]
Continue reading…

 

In setting up a small office network, the network administrator decides to assign private IP addresses dynamically to workstations and mobile devices. Which feature must be enabled on the company router in order for office devices to access the internet?

Last Updated on November 23, 2020 by Admin In setting up a small office network, the network administrator decides to assign private IP addresses dynamically to workstations and mobile devices. Which feature must be enabled on the company router in order for office devices to access the internet? MAC filtering QoS UPnP NAT Answers Explanation […]
Continue reading…

 

Refer to the exhibit. A PC at address 10.1.1.45 is unable to access the Internet. What is the most likely cause of the problem?

Last Updated on November 23, 2020 by Admin Refer to the exhibit. A PC at address 10.1.1.45 is unable to access the Internet. What is the most likely cause of the problem? The wrong netmask was used on the NAT pool. The inside and outside interfaces have been configured backwards. The NAT pool has been […]
Continue reading…

 

Consider the following output for an ACL that has been applied to a router via the access-class in command. What can a network administrator determine from the output that is shown?

Last Updated on November 23, 2020 by Admin Consider the following output for an ACL that has been applied to a router via the access-class in command. What can a network administrator determine from the output that is shown? R1# <output omitted> Standard IP access list 2 10 permit 192.168.10.0, wildcard bits 0.0.0.255 (2 matches) […]
Continue reading…

 

Refer to the exhibit. An administrator configures the following ACL in order to prevent devices on the 192.168.1.0 subnet from accessing the server at 10.1.1.5: Where should the administrator place this ACL for the most efficient use of network resources?

Last Updated on November 23, 2020 by Admin Refer to the exhibit. An administrator configures the following ACL in order to prevent devices on the 192.168.1.0 subnet from accessing the server at 10.1.1.5: access-list 100 deny ip 192.168.1.0 0.0.0.255 host 10.1.1.5 access-list 100 permit ip any any Where should the administrator place this ACL for […]
Continue reading…

 

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 10.27.27.0 255.255.255.0. What wildcard mask would the administrator use in the OSPF network statement?

Last Updated on November 23, 2020 by Admin An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 10.27.27.0 255.255.255.0. What wildcard mask would the administrator use in the OSPF network statement? 0.0.0.15 0.0.0.31 0.0.0.63 0.0.0.255 For more question and answers: Click Here CCNA3 v7 – ENSA Final Exam […]
Continue reading…

 

Refer to the exhibit. Which conclusion can be drawn from this OSPF multiaccess network?​

Last Updated on November 23, 2020 by Admin Refer to the exhibit. Which conclusion can be drawn from this OSPF multiaccess network?​ ​All DROTHER routers will send LSAs to the DR and BDR to multicast 224.0.0.5. ​When a DR is elected all other non-DR routers become DROTHER. If the DR stops producing Hello packets, a […]
Continue reading…